Showing 201 to 220 out of 248
Black leather saddle holsters for the large and heavy Colt Dragoon pistols. Overall, the leather is in good condition but the yoke between the holsters shows heavy surface finish loss. Each side of… (490-2779). Learn More »
Early hand-made powder measure for long hunting rifles. Measures 4.25" long overall with the tube being 4" long by 3/8" in diameter. A nice accessory for a long rifle. [jet]… (490-2896). Learn More »
$225.00
SOLD
This is a nice brown leather “Slim Jim” holster for M1851 and M1861 Colt Navy conversions. Holster body is one piece sewn down the back seam. Stitching remains strong and unbroken. Geometric… (1142-128). Learn More »
Wooden shipping crate for 10 sharps carbines. Crate is missing the lid but is marked on one end with a clear date of “AUGUST 1876.” The same edge has some faint markings that look to read “10… (172-5755). Learn More »
Priced to Sell – These are non-excavated cartridges for the .50 caliber Maynard carbine. Lead bullet with flat nose and a single groove in a brass case with large disc soldered to the bottom. A… (490-768). Learn More »
Some 200,000 thousand firearms captured or collected by CS Ordnance teams and civilians, along with perhaps another 50,000 turned in by CS units, went through the cleaning and/or repair… (1164-13). Learn More »
$3,250.00
ON HOLD
There are no appreciable differences between the NM1863 and NM1865 Sharps other than the stamped model designation by the company, and its occasional absence, which some have speculated was due to… (490-2531). Learn More »
Sharps Model 1855 arms are scarce. Just under 1,000 went to the American market: 600 US Army carbines (on two contracts of 400 and 200 guns each,) about 350 Navy rifles and carbines, and a dozen or… (490-2664). Learn More »
Iron scissor-type mold to cast a lead round ball for revolvers. Measures approximately 3.5” long overall. Single cavity mold with spout. Sprue cutter is formed between the two handles. Cavity… (1164-46). Learn More »
This original German longarm is a .72 caliber, Potsdam Model 1809 smoothbore musket in good condition. Musket measures a total length of almost 56.25” with a 41.25” long barrel and has been… (172-5783). Learn More »
Here is an original, seldom-seen Frank Wesson single-shot breechloader in excellent condition, one of the best that we have handled. This 1st Type, twin-trigger, .44 caliber rimfire, Wesson rifle made… (779-09). Learn More »
This is a Model 1861, .58 caliber, percussion rifle musket in good condition. Produced by E. Remington & Sons, Ilion, New York. Remington produced 40,000 rifles from 1864 to 1866. All gun metal on… (172-5729). Learn More »
This very large flask has to have been for shotguns. Constructed with a copper body, with brass top and spout. Measures approximately 11” tall x 5” at widest point. Unadorned body. Thumb tab and… (172-5639). Learn More »
This flask is for early pocket model revolvers. Constructed with a copper body, with brass top and spout. Measures approximately 6” tall x 2.75” at widest point. Both sides are plain. Thumb tab… (172-5638). Learn More »
This is a black leather holster made for revolvers. The leather still shows the “profile” of a revolver cylinder and barrel. A .31 caliber “pocket” model with long barrel fits into this… (172-5636). Learn More »
This is a Smith & Wesson, No. 2, Old Model Army Revolver. It is a .32 caliber, six-shot revolver with a 5” barrel, rosewood handles. Post-Civil War serial number 60737. Production began in 1861,… (1000-452). Learn More »
This is a tool for clearing the vent of any obstructions. It has an octagonal head with a hole in the center, and a 17” wire brazed to it. The wire comes to a point at the end. The flat head is… (1117-46). Learn More »
Fabricated by Ludlow Brothers of Birmingham, England. Nice display in a 8.25” x 12.25” Riker case. Photocopy of an original wrapper at top with info sheet below, and then the cartridge at the… (M24055). Learn More »
Iron bullet mold measures approximately 7 ½” long. Two halves pinned with rivet and has floating sprue cutter. Iron is pitted but not badly; could be “dug” or out of a barn. Still opens and… (1117-238). Learn More »
This is a black leather holster made to accommodate the Kerr revolver. The leather still shows the “profile” of a revolver cylinder. The holster “pocket” measures approximately 9 ¼” along… (1117-97). Learn More »
Showing 201 to 220 out of 248
Historical Firearms Stolen From The National Civil War Museum In Harrisburg, Pa »
Theft From Gravesite Of Gen. John Reynolds »
Cavalry Carbine Sling Swivel »
Fine Condition Brass Infantry Bugle Insignia »
Scenes of Civil War army camps and depots often give a real chance at seeing army life up close, in detail, and unposed as men go about their tasks unaware of the camera. Sometimes identified as a taken near City Point along the James River, this… (1054-688). Learn More »